[Q11-Q34] 2026 Updated 156-836 Tests Engine pdf – All Free Dumps Guaranteed!

5/5 - (1 vote)

2026 Updated 156-836 Tests Engine pdf – All Free Dumps Guaranteed!

Latest CCME 156-836 Actual Free Exam Questions

The Check Point Maestro is a network security platform that enables organizations to scale their security gateways and manage them as a single entity. It provides a centralized management console that simplifies the configuration, deployment, and monitoring of security gateways. The Maestro platform uses advanced technologies, such as load balancing and traffic management, to ensure high availability and performance. The Check Point Certified Maestro Expert – R81 (CCME) exam validates the candidate’s ability to work with this advanced platform, and to use it to manage and secure large-scale networks.

NO.11 At a minimum, how many management and Uplink ports does a SG require?

Only one of the two interfaces is needed for the Security Group.

Neither are required.

Two of each.

One each.

NO.12 On the MHO, to view connected ports and their functions, use the following command:

asg_ifconfig

show ports

orch_stat -c

orch_stat -p

NO.13 What is the purpose of Management ports located on the Rear Panel of the Orchestrator MHO-140?

1Gbps connectivity for Security Groups

Reserved for internal purposes. Not in use.

Out-of-band interfaces for access to Orchestrator itself

Additional ports used as uplinks

NO.14 The core four manual diagnostic tools include:
asg diag verify, asg perf -v, orch_stat -all, and

asg diag verify

cpinfo

hcp -r all

asg stat -v

NO.15 What Maestro component is automatically designated the SMO Master?

The SGM with the lowest member ID (the first one added to the security group.)

The MDS that pushes policy to the SMO is considered the SMO Master.

The first MHO configured is considered the SMO Master.

The SGM with the highest member ID (the last one added to the security group.)

NO.16 What kinds of transceivers are supported on Orchestrator MHO-140?

SFP, QSFP, QSFP28

SFP+, SFP28, QSFP

SFP, SFP+, SFP28

SFP, SFP+, QSFP, QSFP28

NO.17 Multiple SGs can exist in a Dual Site environment. Each SG can be configured in one of three ways. Which is not one of those ways?

Two MHOs connected to two MHOs via load balancers.

Two MHOs at same site connected to remote site MHOs via two different switches.

Two MHOs at same site connected to remote site MHOs via single switch.

Direct connectivity between Remote Site MHOs.2

NO.18 What cannot be learned from the output of asg monitor command?

Uptime

Port status

Security Policy status

Appliances cluster status

NO.19 HealthCheck Point _____

is a self-updatable suite of tools for MHOs with the capability to assess the health of the system and provide a timeline of critical and informative events that might have occurred in a production system.

performs a system health check and is meant to replace both a CPInfo and the health check script.

can be used to let you visualize the Firewall topology for the SG and view live statistics, which includes throughput, problem notes, and CPU utilization.

is a self-updatable suite of tools for SGMs with the capability to assess the health of the system, visualize the Firewall topology, provide a timeline of critical and informative events that might have occurred in a production system.

NO.20 Splitter cannot be used _______

To connect single port on orchestrator to the same Appliance

To connect single port on orchestrator to multiple port on external switch

To connect single port on Appliance to multiple ports on the orchestrator

To connect single port on orchestrator to multiple Appliances

NO.21 What kinds of transceivers are supported on Orchestrator MHO-140?

SFP, QSFP, QSFP28

SFP+, SFP28, QSFP

SFP, SFP+, SFP28

SFP, SFP+, QSFP, QSFP28

NO.22 There is a Security group of 10 Appliances and all of them are up and running. How many Appliances within a Security Group keep the same connection in its connection table in case of NAT?

Between 2 and 4

All 10

NO.23 Which command is used to set the number of sites in a Maestro environment?

set maestro orchestrator-site-amount

set maestro configuration orchestrator-site-amount

set maestro configuration orchestrator-site-number

set maestro configuration orchestrator-site-id

NO.24 There are two appliances within the same Security Group. One of them is connected by One downlink only, another one by Two downlinks. Assuming there’s no NAT and no VPN, what would be proportion of traffic distribution done by Orchestrator?

100%/0%

33%/66%

50%/50%

66%/33%

NO.25 How does HyperSync work in a Dual Site environment?

Each active connection has two local backups (on the local site) and a third backup connection on the second site (remote site.)

Each active connection has a local backup (on the local site) and a second backup connection on the second site (remote site.)

Each active connection has a local backup (on the local site) and a second backup connection on each of the MHOs.

Each active connection has a backup connection on the second site (remote site.)

NO.26 What is the default Distribution mode?

Auto-topology

User

Manual-General

Network

NO.27 What cannot be learned from the output of lldpctl?

Serial number of Appliance

Appliance model

Distribution mode

Orchestrator’s IP

NO.28 What is a security group?

A solution for Security Gateway redundancy and Load Sharing.

A set of appliances of the same model that are collectively managed by the MHO.

A set of network interfaces and individual SGMs assigned to a logical group.

A set of objects in SmartConsole that are responsible for enforcing an access policy.

NO.29 What is the purpose of Management ports located on the Rear Panel of the Orchestrator MHO-140?

1Gbps connectivity for Security Groups

Reserved for internal purposes. Not in use.

Out-of-band interfaces for access to Orchestrator itself

Additional ports used as uplinks

NO.30 There are two 10Gbps dual-port NICs and one 40Gbps NIC installed on a 23800 Appliance in slots 1, 2 and 3 accordingly. Which interfaces should be connected to Orchestrator 1 for downlinks’ intra- orchestrator redundancy when using two Orchestrators?

Port 1 in Slot 2 and Port 2 in Slot 1

This configuration is not supported

Any pair of available ports

Port 1 in Slot 1 and Port 2 in Slot 1

NO.31 Logs without a dedicated log file can be found in

/var/log/junk.log.dbg

/var/log/messages

$RTDIR/log/junk.log

$FWDIR/log/fw.log

NO.32 For the MHO-175, which ports are Management ports?

Ports 49 – 55 are Management ports.

Ports 1 – 4 are Management ports.

Ports 27 – 47 are Management ports.

Ports 5 – 26 are Management ports.

NO.33 Where should sx_api_ports_dump.py command be ran?

Management server

Security Group

Orchestrator

SMO Appliance

NO.34 Which command should be used to restart Orchestrator service only?

orchd restart

reboot

service orchestrator restart

cpstop; cpstart

156-836 Dumps Updated Practice Test and 90 unique questions: https://www.surepassexams.com/156-836-exam-bootcamp.html

Leave a Reply Cancel reply