[Nov-2022] NACE NACE-CIP2-001 Dumps – Reduce Your Chance of Failure in NACE-CIP2-001 Exam [Q19-Q39]

Rate this post

[Nov-2022] NACE NACE-CIP2-001 Dumps – Reduce Your Chance of Failure in NACE-CIP2-001 Exam

To help you achieve your ultimate goal, we suggest the actual NACE NACE-CIP2-001 dumps for your Coating Inspector Level 2 exam preparation to use as your guideline.

QUESTION 19
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?

Sacking

Acid etching

Stoning

High-pressure water washing

QUESTION 20
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:

Refuse to take readings until an is in place

Develop your own methodology and proceed take the readings

Use a generally accepted industry standard and to take readings

Call your supervisor

QUESTION 21
Measuring methyl ethyl ketone (MEK) resistance of ethyl silicate inorganic zinc-rich primers by solvent rub requires

25 single rubs with a saturated cloth.

35 single rubs with a saturated cloth.

50 double rubs with a saturated cloth.

25 double rubs with a saturated cloth.

QUESTION 22
Inspection and Test Plans are provided to:

Outline the inspection steps, sequencing and pass/fail criteria

So the Inspector doesn’t have to read the entire specification

To supersede the requirements of the product data sheets

So the contractor has a single document to reference

QUESTION 23
When using a destructive Paint Inspection Gauge the NACE inspector must:

Determine the Dry Film Thickness of the coating prior to use

Ensure the glue on the dolly is properly applied prior to use

Consult SSPC Guide 1 prior to use

Select the appropriate hand wheel based on the measured Dry Film Thickness prior to us

QUESTION 24
Application of Thermal Spray Coatings requires:

The same skills as liquid coatings

Specialized skills supported by training and experience

No particular skills

The same skills as welding

QUESTION 25
Pre-cleaning of work pieces will NOT remove

snow, ice or water.

oil or grease.

dirt.

mill scale.

QUESTION 26
Coating application to concrete substrates is:

More challenging than coating steel

Less challenging, than coating steel

The same as coating steel

Not required as Concrete is inorganic

QUESTION 27
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:

True

False

QUESTION 28
Inspectors perform tests on linings that they may not perform on exterior coatings because

coatings are more durable than linings.

coatings are expected to degrade over time.

linings protect the contents and the container.

linings are more durable than coatings.

QUESTION 29
You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:

Request that the Contractor re-blast the floor

Review the standard with the Contractor and re-inspect the floor

Shut the job down

Call your supervisor

QUESTION 30
In the event of a conflict between the Product Data Sheet and the Specification:

The Product Data Sheet prevails

The Specification prevails

It is up to the Inspector to decide which one to follow

It is up to the Applicator to decide which one to follow

QUESTION 31
Linings are used on the interior of pipelines to

provide protection against soil chemicals.

afford limited temperature insulation.

protect the transported product.

reduce magnetic polarity.

QUESTION 32
Non-Conformance Reports are designed to:

Punish the Contractor for substandard work

Elevate the status of the Inspector

Assist the Owner in negotiating credits from the Contractor

To identify items that do not meet the specification requirements

QUESTION 33
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?

Gathering

Midstream

Transmission

Distribution

QUESTION 34
You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 you notice significant documentation errors.
Your FIRST preferred course of action is to:

Correct the errors yourself and suggest the Level 1 inspector be replaced

Correct the errors yourself and advise your supervisor that the Level 1 Inspector is incompetent

Have the Level 1 Inspector correct the errors and set up remedial training to improve the quality of documentation

Correct the errors yourself and submit the reports without any further action

QUESTION 35
Which surface preparation method uses a dilute acid solution to remove laitance and I roughen the concrete surface?

Sacking

Acid etching

Stoning

High-pressure water washing

QUESTION 36
When performing testing in accordance with ASTM D 2583 the inspector may observe:

Adhesion failure

Cohesion failure

Glue failure

Cold flow or creep

QUESTION 37
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:

Stop the job

Require the Applicator to remove the coating

Advise the Owner and write a Non-Conformance report

Ignore the situation

QUESTION 38
Galvanizing performs best in which of the following exposures:

pH below 4

pH above 12

pH between 5-10

pH of 13

QUESTION 39
Corrosion is the reverse process of

hot dipping.

steel manufacturing.