[2023] HPE6-A72 All-in-One Exam Guide Practice To your HPE6-A72 Exam! [Q49-Q70]

5/5 - (1 vote)

[2023] HPE6-A72 All-in-One Exam Guide Practice To your HPE6-A72 Exam!

Preparations of HPE6-A72 Exam 2023 Aruba Certified Switching Associate (ACSA) V1 Unlimited 90 Questions

Q49. SW1(config)# interface 1/1/1-1/1/2
SW1(config-if-<1/1/1-1/1/2)# vlan access 2
SW1(config-if-<1/1/1-1/1/2)# exit
SW1(config)# interface 1/1/11-1/1/17
SW1(config-if-<1/1/11-1/1/17)# vlan access 17
SW1(config-if-<1/1/11-1/1/17)# exit
After completing the above commands, what is the expected output of show vlan with no other vlan commanded having been added?

Option A

Option B

Option C

Option D

Q50. Core# configure terminal
Core(config)# vrf Green
Core(config-vrf)# exit
Core(config)#
Core(config)# interface vlan 50
Core(config-if-vlan)# ?
Given the configuration on the CORE switch shown above, what command would follow to assign the switched virtual interface (SVI) vlan 50 to the VRF created?

Core(config-if-vlan)# vrf attach Green

Core(config-if-vlan)# ip vpn-instance Green

Core(config-if-vlan)# ip vrf forwarding Green

Core(config-if-vlan)# routing-context Green vrf

Q51. What are two methods for remotely managing an Aruba AOS-CX switch? (Choose two.)

SNMPv2c

HTTPS

USB-C console

Telnet

SSH

Q52. Refer to the exhibit.

You are in the process of configuring VSF between Access-1 and Access-2. Access-1 has been configured as the VSF Master.
What is a valid configuration for Access-2 to join the VSF stack?

Access-2# configure
Access-2(config)# vsf member 1 Access-2(config)# vsf renumber-to 2 Access-2(vsf-member-1)# link 2 2/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y

Access-2# configure
Access-2(config)# vsf member 2 Access-2(vsf-member-1)# link 2 1/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y

Access-2# configure
Access-2(config)# vsf member 2 Access-2(vsf-member-1)# link 1 1/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y

Access-2# configure
Access-2(config)# vsf member 1 Access-2(vsf-member-1)# link 1 1/1/28 Access-2(vsf-member-1)# exit Access-2(config)# vsf renumber-to 2

This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y

Q53. What are two mechanisms supported on AOS-CX 6300 switches used in Multi-active Detection to determine the status of the Primary member? (Choose two.)

Management interface split detection

Peer switch-based detection

Loopback keepalives

ARP-based

BFD

Q54. Which command can be used to find the serial number of an Aruba OS-CX switch?

The command inventory

The command version

The command show running-configuration

The command show system

Explanation/Reference:

Q55. Which port or ports should be allowed through a firewall so that an AOS-CX switch can act as an SNMP Agent?

UDP 1812 and UDP 1813

UDP 161

TCP 443

UDP 162

Q56. Click on the colored box that corresponds with the line that best represents Broadcast traffic flow.

Q57. Refer to the exhibit.

What is the correct binary conversion of the last two hexadecimal characters of the physical address?

1101 1000

1110 1101

1001 1111 0101 0011

1000 1101 1110 1101

Q58. Click on the colored box that corresponds with the line that best represents Unicast traffic flow.

Q59. The customer has 778 developers testing computer games on the network.
Which two actions resolve Broadcast storms? (Choose two.)

Manually disable the redundant link to immediately resolve the impacted portion of the network.

Utilize Spanning Tree to dynamically disable all redundant links in a segment.

Setting switch ports to half-duplex will resolve Broadcast storms using Carrier Sense Multiple-Access Collision Detection (CSMA/CD).

Enable single Area Open Shortest Path First (OSPF) on all Layer 2 switches, but do not enable routing.

Utilize Spanning Tree to dynamically block Designated ports in addition to Alternate ports.

Q60. The section in blue can be ignored.
SW1(config)# interface 1/1/1-1/1/2
SW1(config-if-<1/1/1-1/1/2)# vlan access 2
SW1(config-if-<1/1/1-1/1/2)# exit
SW1(config)# interface 1/1/11-1/1/17
SW1(config-if-<1/1/11-1/1/17)# vlan access 17
SW1(config-if-<1/1/11-1/1/17)# exit
After completing the above commands, what is the expected output of show vlan with no other vlan commanded having been added?

Option A

Option B

Option C

Option D

Q61. Which statement is correct regarding powering an Aruba Access Point?

PoE or PoE+ is only used with Ethernet that is carried over multi-mode fiber cabling.

Using switchports for this reason is unnecessary, because Aruba Access Points typically use an AC to DC power adapter to draw power.

PoE or PoE+ enabled switchports are rarely used given concerns about causing electrical interference, with the data also carried over Ethernet cabling.

Most administrators use PoE or PoE+ enabled switchports to provide both Ethernet connectivity and power to the AP.

Q62. Match the term to the correct description.

Q63. Match each network protocol to the correct server listening port. Not all answers will be used.

Q64. What are two available options as part of a DHCP offer message? (Choose two.)

SSID

DNS server IP

Subnet Mask

LLDP-MED

VLANID

Q65. Match each description to the correct management tool for Aruba AOS-CX.

Q66. What is the login and password combination is used when first configuring an Aruba OS-CX switch from factory defaults?

Q67. What is Deep Packet Inspection?

a machine learning method of packet inspection for the purpose of choosing which dynamic routing protocol to automatically assign

a concept that applies to firewalls, when examining packets only up through Layer 4

a function of Policy Based Routing that examines the entire IPv4 header to forward traffic based on factors other than destination address

a firewall process of examining the packet header all the way to Layer 7 in order to determine if the packet should be permitted or denied

Q68. Click on the colored box that corresponds with the line that best represents Unicast traffic flow.

Q69. Refer to the exhibit.

What VSF command produces the above output?

show vsf member

show vsf link

show vsf topology

show vsf detail

Q70. Which Ethernet port combination does the Aruba 5400R ZL2 switch series support?

10/100 Megabit Ethernet, Gigabit Ethernet, and 100 Gigabit Ethernet

Gigabit Ethernet, 25 Gigabit Ethernet, and 40 Gigabit Ethernet

10/100 Megabit Ethernet, Gigabit Ethernet, 25 Gigabit Ethernet, and 100 Gigabit Ethernet

10/100 Megabit Ethernet, Gigabit Ethernet, and 40 Gigabit Ethernet

Loading …

HP HPE6-A72 (Aruba Certified Switching Associate) Exam is a certification exam designed for IT professionals who are interested in gaining knowledge and skills in the field of computer networking. HPE6-A72 exam is intended for those who have experience working with ArubaOS-Switches and are looking to validate their skills and knowledge in this area.

Focus on HPE6-A72 All-in-One Exam Guide For Quick Preparation: https://www.surepassexams.com/HPE6-A72-exam-bootcamp.html

Leave a Reply Cancel reply