Dumps Moneyack Guarantee – API-570 Dumps UpTo 50% Off [Q46-Q62]

Rate this post

Dumps Moneyack Guarantee – API-570 Dumps UpTo 50% Off

Updated Dec-2023 Pass API-570 Exam – Real Practice Test Questions

Q46. What document may be used as a guide when examiners are being qualified by their employer?

ASME Section IX

ASM E Section V

ASNT SNT- TC-1A

API 570

Q47. Each piece of magnetizing equipment shall be calibrated

at the beginning of each shift

at least once a year or whenever the equipment has been subject to major electrical repair

whenever the technician feels like it

at least once every 90 days

Q48. Who has the responsibility for qualifying welding procedures?

Each employer

Each subcontractor

Each welder

Each contractor

Q49. Penrtrameters (IQls) shall either be____or_____and shall be manufactured and identified in accordance with ASME.

black-type white-type

step wedge calibration block

hole-type wire-type

pica-type elite-type

Q50. What is the definition of normalizing?

Rapid cooling of a heated metal

Heating an alloy to a suitable temperature, holding that temperature long enough to allow constituents to enter into solid solution and then cooling ~ rapidly enough to hold the constituents.

Process where a ferrous metal is heated to a suitable temperature above the transformation range and is subsequently cooled in still air at room temperature.

Heating to and holding at a suitable temperature and then cooling at a suitable rate to reduce hardness, improve machinability, facilitate cold working, etc.

Q51. If the supporting PQR is used, are the P-no’s correct on the attached WPS?

Yes

Could be if properly preheated

Not enough information

Q52. The repair organization shall maintain records of welding procedures and welder qualifications and make the records available to the inspector_____.

prior to the start of welding

any time during welding

after completion of welding

when the repair organization releases the information

Q53. Temperatures above can damage transducers not equipped with delay line material.

There is no limit to temperature

manufacturer’s specification

280 psi

1,000 psi

Q54. On the regularly furnished Class 300 raised face flange, what is the height of the raised face?

0.06″

0.09″

0.19″

0.25″

Q55. A DC yoke shall have a lifting power of at least

5 lbs.

8 lbs.

10 lbs.

40 lbs.

Q56. In a piping circuit, which of the following does not routinely have thickness measurements taken?

Valves

Straight Run Pipe

Fittings

Dead legs

Q57. During a MT examination, shall be performed on each area.

100% coverage at the required sensitivity

a calibration of each piece of magnetizing equipment

at least three separate examinations

prod spacing of at least

Q58. Hammer testing of piping is a common practice. However, which of the following should never be hammered?

Cast iron piping

Caustic piping

All welded piping

Both A and B

Q59. Geometric unsharpness of the radiograph of a component under 2″ th1ck shall not exceed

0.020″

0.030″

0.040″

0.050″

Q60. For a single wall material thickness, over 0.375″ through 0.50″, what is the hole type designation for a source side penetrameter

Q61. When can welding procedures qualified by other than the employer be used?

When there is specific approval of the inspector

When the job contract gives authorization

When the procedure is used only one time

When the production weld is radiographed

Q62. What is the maximum thickness measurement inspection interval for an injection point?

3 years

5 years

10 years

By Class

Loading …

API-570 certification exam is a challenging but rewarding achievement for piping inspectors who want to demonstrate their knowledge and expertise in their field. It is a respected qualification in the oil and gas industry, and passing the exam can lead to new career opportunities and professional development.

Download Free API API-570 Real Exam Questions: https://www.surepassexams.com/API-570-exam-bootcamp.html

Leave a Reply Cancel reply