100% Free HPE7-A01 Exam Dumps to Pass Exam Easily from SurePassExams [Q54-Q72]

Rate this post

100% Free HPE7-A01 Exam Dumps to Pass Exam Easily from SurePassExams

Free HPE7-A01 Exam Questions HPE7-A01 Actual Free Exam Questions

HP HPE7-A01 exam is a comprehensive certification program that is designed to test the knowledge and skills of IT professionals in network access solutions. Aruba Certified Campus Access Professional Exam certification program is recognized globally and is intended for IT professionals who are responsible for designing, implementing, and managing network access solutions in various organizations. By passing HPE7-A01 exam, IT professionals can validate their expertise in network access solutions and enhance their career opportunities in the IT industry.

NEW QUESTION 54
Your Director of Security asks you to assign AOS-CX switch management roles to new employees based on their specific job requirements. After the configuration was complete, it was noted that a user assigned with the auditors role did not have the appropriate level of access on the switch.
The user was not allowed to perform firmware upgrades and a privilege level of 15 was not assigned to their role. Which default management role should have been assigned for the user?

sysadmin

sysops

administrators

config

NEW QUESTION 55
Refer to the exhibit.

With Core-1. what is the default value for config-revision?

1-0

0. 0

NEW QUESTION 56
Which component is used by the Aruba Network Analytics Engine (NAE)?

JSON-based scripts

Lisp-based agents

Ruby-based scripts

Current State Database

NEW QUESTION 57
Match each PoE power class to Its corresponding 802.3 standard. (Options may he used more than once or not at all)

NEW QUESTION 58
You are helping an onsite network technician bring up an Aruba 9004 gateway with ZTP for a branch office The technician was to plug in any port for the ZTP process to start Thirty minutes after the gateway was plugged in new users started to complain they were no longer able to get to the internet. One user who reported the issue stated their IP address is 172.16 0.81 However, the branch office network is supposed to be on 10.231 81.0/24.
What should the technician do to alleviate the issue and get the ZTP process started correctly?

Move the cable on the gateway to G0/0/1. and add the device’s MAC and Serial number in Central

Turn off the DHCP scope on the gateway, and set DNS correctly on the gateway to reach Aruba Activate

Factory default and reboot the gateway to restart the process.

Move the cable on the gateway from port G0/0V1 tc port G0 0.0

NEW QUESTION 59
You are setting up a customer’s 15 headless loT devices that do not support 802.1X. What should you use?

Multiple Pre-Shared Keys (MPSK) Local

Clearpass with WPA3-PSK

Clearpass with WPA3-AES

Multiple Pre-Shared Keys (MPSK) with WPA3-AES

NEW QUESTION 60
you need to have different routing-table requirements With Aruba CX 6300 VSF configuration.
Assuming the correct layer-2 VLAN already exists, how would you create a new SVI for a separate routing table?

create a new VLAN, and attach the VRF to it.

Create a new routing table, and attach VLANS to it

Create a new SVI and use attach command.

Create a new VLAN. and attach the routing table to it

NEW QUESTION 61
Match the topics with the underlying technologies (Options may be used more than once or not at all.)

NEW QUESTION 62
In an ArubaOS 10 architecture using an AP and a gateway, what happens when a client attempts to join the network and the WLAN is configured with OWE?

Authentication information is not exchanged

The Gateway will not respond.

No encryption is applied.

RADIUS protocol is utilized.

NEW QUESTION 63
How is Multicast Transmission Optimization implemented in an HPE Aruba wireless network?

“The optimal rate for sending multicast frames is based on the highest broadcast rate across all associated clients

When this option is enabled the minimum default rate for multicast traffic is set to 12 Mbps for 5 GHz

The optimal rate for sending multicast frames is based on the lowest broadcast rate across all associated clients.

The optimal rate for sending multicast frames is based on the lowest unicast rate across all associated clients.

NEW QUESTION 64
You need to have different routing-table requirements with Aruba CX 6300 VSF configuration Assuming the correct layer-2 VLAN already exists how would you create a new OSPF configuration for a separate routing table?

Create a new OSPF area, and attach VRF name.

Create a new OSPF process ID with vrf name.

Attach a new OSFP process ID with a custom routing table

Attach OSPF process ID in the VRF configuration.

NEW QUESTION 65
With the Aruba CX switch configuration, what is the first-hop protocol feature that is used for VSX L3 gateway as per Aruba recommendation?

Active Gateway

Active-Active VRRP

SVI with vsx-sync

VRRP

NEW QUESTION 66
How is Multicast Transmission Optimization implemented in an HPE Aruba wireless network?

“The optimal rate for sending multicast frames is based on the highest broadcast rate across all associated clients

When this option is enabled the minimum default rate for multicast traffic is set to 12 Mbps for 5 GHz

The optimal rate for sending multicast frames is based on the lowest broadcast rate across all associated clients.

The optimal rate for sending multicast frames is based on the lowest unicast rate across all associated clients.

NEW QUESTION 67
You need to ensure that voice traffic sent through an ArubaOS-CX switch arrives with minimal latency What is the best scheduling technology to use for this task?

Strict queuing

Rate limiting

QoS shaping

DWRR queuing

NEW QUESTION 68
You are configuring Policy Based Routing (PBR) for a subnet that will be used to test a new default route for your network Traffic originating from 10.2.250.0/24 should use a new default route to 10.1.1.253. Other non-default routes for this subnet should not be affected by this change.
What are two parts of the solution for these requirements? (Select two.)

NEW QUESTION 69
Refer to Exhibit:

A company has deployed 200 AP-635 access points. To take advantage of the 6 GHz band, the administrator has attempted to configure a new WPA3-OWE SSID in Central but is not working as expected.
What would be the correct action to fix the issue?

Change the SSID to WPA3-Enterprise (CNSA).

Change the SSID to WPA3-Personal.

Change the SSID to WPA3-Enhanced Open.

Change the SSID to WPA3-Enterprise (CCM).

NEW QUESTION 70
Which statements are true about VSX LAG? (Select two.)

The total number of configured links may not exceed 8 for the pair or 4 per switch

Outgoing traffic is switched to a port based on a hashing algorithm which may be either switch in the pair

LAG traffic is passed over VSX ISL links only while upgrading firmware on the switch pair

Outgoing traffic is preferentially switched to local members of the LAG.

Up to 255 VSX lags can be configured on all 83xx and 84xx model switches.

The correct answers are A and D.
According to the web search results, VSX LAG is a feature that allows multiple PSKs to be used on a single SSID, providing device-specific or group-specific passphrases for enhanced security and deployment flexibility for headless IoT devices1. VSX LAGs span both aggregation switches and appear as one device to partner downstream or upstream devices or both when forming a LAG with the VSX pair2.
One of the statements that is true about VSX LAG is that the total number of configured links may not exceed 8 for the pair or 4 per switch1. This means that a VSX LAG across a downstream switch can have at most a total of eight member links, and a switch can have a maximum of four member links. When creating a VSX LAG, it is recommended to select an equal number of member links in each segment for load balancing1.
Another statement that is true about VSX LAG is that outgoing traffic is preferentially switched to local members of the LAG2. This means that when active forwarding and active gateway are enabled, north-south and south-north traffic bypasses the ISL link and uses the local ports on the switch. This optimizes the traffic path and reduces the load on the ISL link2.
The other statements are false or not relevant for VSX LAG. Outgoing traffic is not switched to a port based on a hashing algorithm, which may be either switch in the pair. This is a characteristic of MLAG (Multi-Chassis Link Aggregation), which is a different feature from VSX LAG. LAG traffic is not passed over VSX ISL links only while upgrading firmware on the switch pair. This is a scenario that may occur when performing hitless upgrades, which is a feature that allows software updates without impacting network availability. The number of VSX lags that can be configured on all 83xx and 84xx model switches is not 255, but depends on the switch model and firmware version. For example, the AOS-CX 10.04 supports up to 64 VSX lags for 8320 switches and up to 128 VSX lags for 8325 and 8400 switches.

NEW QUESTION 71
Which statement best describes QoS?

Determining which traffic passes specified quality metrics

Scoring traffic based on the quality of the contents

Identifying specific traffic for special treatment

Identifying the quality of the connection

NEW QUESTION 72
Which component is used by the Aruba Network Analytics Engine (NAE)?

JSON-based scripts

Lisp-based agents

Ruby-based scripts

Current State Database

To earn the HPE7-A01 certification, candidates must pass a single exam that covers topics such as ArubaOS, wireless LAN fundamentals, RF fundamentals, and network design. HPE7-A01 exam consists of 60 multiple-choice questions and has a time limit of 90 minutes. A passing score of 75% is required to earn the certification.

Latest 100% Passing Guarantee – Brilliant HPE7-A01 Exam Questions PDF: https://www.surepassexams.com/HPE7-A01-exam-bootcamp.html

Leave a Reply Cancel reply