Prepare PD1-001 Question Answers Free Update With 100% Exam Passing Guarantee [Q496-Q511]

Rate this post

Prepare PD1-001 Question Answers Free Update With 100% Exam Passing Guarantee [2022]

Dumps Real CompTIA PD1-001 Exam Questions [Updated 2022]

NEW QUESTION 496
During the laser printing process, which of the following steps occurs right before the latent image is written on the photoconductor?

Fusing

Transferring

Development

Charging

NEW QUESTION 497
Which of the following is a common form of memory card used to store information?

RAW

LPT

NEW QUESTION 498
Which of the following components would be used to measure toner density or a test patch on the photoconductor?

Interrupt sensor

Toggle switch

Reflector sensor

Magnet switch

NEW QUESTION 499
Which of the following steps should be taken after the technician has determined that the serviced unit has been repaired?

Perform a complete preventive maintenance (PM) to insure the repair is complete.

Run a complete test using all paper trays and finishing options.

The repair is finished, if the problem reoccurs, the customer will call back.

Schedule a follow up for the next week to confirm the unit is working correctly.

NEW QUESTION 500
When scanning a color document with a single pass scanner which of the following is used to separate the colors for processing?

Color filters

Color lenses

Color mirrors

Color lamps

NEW QUESTION 501
A customer has a document that was formatted for large size media but needs to print the document in a smaller size. In which of the following would this adjustment occur?

Device control panel

Printer Driver

Web interface

Scan Driver

NEW QUESTION 502
While repairing the printer, a cleaning chemical spil s onto the floor. Which of the following steps need to be taken?

Cal the fire department for a hazardous material spil .

Use the vacuum cleaner to clean up the spill.

Clean up the spill and ventilate the area, if needed.

Avoid touching the spil , place a fan on the spil until it dries up.

NEW QUESTION 503
An ink dispersion printer is brought in for service. The customer is having a problem with the quality of the output. The pictures printed are stil wet and will smear when they are touched. Which of the following should the technician do FIRST?

Check the fuser pressure.

Verify specifications of photo media.

Replace the print head.

Replace the logic PCB.

NEW QUESTION 504
A technician has removed the halogen heating lamp from the fusing unit. Which of the following sections of a multimeter would a technician use to test whether the lamps heating element is broken?

Ohm meter

DC volt meter

Ammeter

Temperature probe

NEW QUESTION 505
Firmware typically resides in which of the following components on an MFD?

In a CCD

On a USB flash drive

In the hard drive

On a circuit board

NEW QUESTION 506
In an ink dispersion printer, which of the following is a type of
ink?

Resin

Lanolin

Iodine

Dye

NEW QUESTION 507
A customer is using a remanufactured toner which has caused damage to the fuser unit and wil require the unit to be cleaned. The unit is covered under warranty, but using remanufactured toner causes the warranty to be voided. This is now a chargeable service. Which of the following is the BEST response from the technician?

You will be receiving a bill after the service is complete. Here is my contact information.

Do not use remanufactured toner; it states that in the warranty. You will be billed for this service call and the parts.

You have voided the warranty so any services will now be charged to your company.

Using remanufactured toner is not covered by manufacturers warranty. Therefore this service call and the parts required will be chargeable.

NEW QUESTION 508
The client reports they cannot fax to one particular location. Al other locations work fine. The activity report confirms this. Which of the following is the next BEST step?

Try sending to it again this time with several pages.

Use a telephone to call the number in question and listen to the line.

Reboot the fax machine and then try again.

Insert the paper in the ADF face up to ensure the image is captured.

NEW QUESTION 509
A customer is printing a document on transparencies using the multipurpose bypass tray on their laser printer; the page was picked up but never exited the printer. Which of the following could cause this issue?

Incorrect media size setting

Defective laser unit

Incorrect media type setting

Incorrect resolution setting

NEW QUESTION 510
A technician is troubleshooting a ghosting image quality problem. Which of the following methods would BEST help isolate the cause?

Connect a voltage tester to the Print Engine Card and inspect voltage on engine contacts.

Inspect the scanner optics for possible contamination.

Enter Service Mode and print multiple pages from each input and to each output bin to ensure all are functioning well.

Stop the printer half way through the printing process and inspect partially printed pages.

NEW QUESTION 511
Which of the following parts would open and close a junction gate in a finishing device? (Select TWO).

Solenoid

Clutch

Stepper Motor

AC/DC Motor

Cams

Loading …